? coilcraft, inc. 2008 specifications subject to change without notice. please check our website for latest information. chip inductors C 1008cs series (2520) document 101-1 document 101-1 revised 09/21/07 j h a b overall f g e terminal f c d terminal wraparound: approx 0.015/0,38 both ends recommended land pattern i i 10 100 frequency (mhz) q factor 1000 10000 100 100 120 90 70 80 60 50 40 30 20 10 0 47 nh 12 nh 330 nh 750 nh 1800 nh 100 nh 1,000 900 800 700 600 500 400 300 200 100 0 frequency (mhz) inductance (nh) 1000 10000 100 10 1 100 nh 47 nh 12 nh 750 nh 330 nh typical q vs frequency typical l vs frequency ab c d max max max ref e f g h i j 0.115 0.110 0.080 0.020 0.080 0.020 0.060 0.100 0.040 0.050 inches 2,92 2,79 2,03 0,51 2,03 0,51 1,52 2,54 1,02 1,27 mm -40 -20 0 20 40 60 80 100 140 120 ambient temperature (c) 120 110 100 90 80 70 60 50 40 30 20 10 0 percent of rated rms i 25c irms derating ? high srf and excellent q values ? tight tolerances, many values at 1% ? 39 inductance values from 10 nh to 8.2 h designer?s kit c300 contains 10 each of all values core material ceramic terminations rohs compliant silver-palladium-platinum-glass frit. other terminations available at additional cost. weight 29.6 ? 37.4 mg ambient temperature ?40c to +125c with i rms current, +125c to +140c with derated current storage temperature component: ?40c to +140c. packaging: ?55c to +80c resistance to soldering heat max three 40 second reflows at +260c, parts cooled to room temperature between cycles temperature coefficient of inductance (tcl) +25 to +125 ppm/c moisture sensitivity level (msl) 1 (unlimited floor life at <30c / 85% relative humidity) mean time between failures (mtbf) 1 billion hours packaging 2000 per 7 reel; 7500 per 13 reel. plastic tape: 8 mm wide, 0.3 mm thick, 4 mm pocket spacing, 2.0 mm pocket depth pcb washing only pure water or alcohol recommended
? coilcraft, inc. 2008 1008cs series (2520) specifications subject to change without notice. please check our website for latest information. document 101-2 document 101-2 revised 09/21/07 inductance 2 percent srf min 5 dcr max 6 i rms 7 part number 1 (nh) tolerance 3 q min 4 (mhz) (ohms) (ma) 1008cs-100x_l_ 10 @ 50 mhz 5,2 50 @ 500 mhz 4100 0.08 1000 1008cs-120x_l_ 12 @ 50 mhz 5,2 50 @ 500 mhz 3300 0.09 1000 1008cs-150x_l_ 15 @ 50 mhz 5,2 50 @ 500 mhz 2500 0.10 1000 1008cs-180x_l_ 18 @ 50 mhz 5,2 50 @ 350 mhz 2500 0.11 1000 1008cs-220x_l_ 22 @ 50 mhz 5,2 ,1 55 @ 350 mhz 2400 0.12 1000 1008cs-270x_l_ 27 @ 50 mhz 5,2 55 @ 350 mhz 1600 0.13 1000 1008cs-330x_l_ 33 @ 50 mhz 5,2 60 @ 350 mhz 1600 0.14 1000 1008cs-390x_l_ 39 @ 50 mhz 5,2 60 @ 350 mhz 1500 0.15 1000 1008cs-470x_l_ 47 @ 50 mhz 5,2 ,1 65 @ 350 mhz 1500 0.16 1000 1008cs-560x_l_ 56 @ 50 mhz 5,2 ,1 65 @ 350 mhz 1300 0.18 1000 1008cs-680x_l_ 68 @ 50 mhz 5,2 ,1 65 @ 350 mhz 1300 0.20 1000 1008cs-820x_l_ 82 @ 50 mhz 5,2 ,1 60 @ 350 mhz 1000 0.22 1000 1008cs-101x_l_ 100 @ 25 mhz 5,2 ,1 60 @ 350 mhz 1000 0.56 650 1008cs-121x_l_ 120 @ 25 mhz 5,2 ,1 60 @ 350 mhz 950 0.63 650 1008cs-151x_l_ 150 @ 25 mhz 5,2 ,1 45 @ 100 mhz 850 0.70 580 1008cs-181x_l_ 180 @ 25 mhz 5,2 ,1 45 @ 100 mhz 750 0.77 620 1008cs-221x_l_ 220 @ 25 mhz 5,2 ,1 45 @ 100 mhz 700 0.84 500 1008cs-271x_l_ 270 @ 25 mhz 5,2,1 45 @ 100 mhz 600 0.91 500 1008cs-331x_l_ 330 @ 25 mhz 5,2 ,1 45 @ 100 mhz 570 1.05 450 1008cs-391x_l_ 390 @ 25 mhz 5,2 ,1 45 @ 100 mhz 500 1.12 470 1008cs-471x_l_ 470 @ 25 mhz 5,2 ,1 45 @ 100 mhz 450 1.19 470 1008cs-561x_l_ 560 @ 25 mhz 5,2 ,1 45 @ 100 mhz 415 1.33 400 1008cs-621x_l_ 620 @ 25 mhz 5,2 ,1 45 @ 100 mhz 375 1.40 300 1008cs-681x_l_ 680 @ 25 mhz 5,2 ,1 45 @ 100 mhz 375 1.47 400 1008cs-751x_l_ 750 @ 25 mhz 5,2 ,1 45 @ 100 mhz 360 1.54 360 1008cs-821x_l_ 820 @ 25 mhz 5,2 ,1 45 @ 100 mhz 350 1.61 400 1008cs-911x_l_ 910 @ 25 mhz 5,2,1 35 @ 50 mhz 320 1.68 380 1008cs-102x_l_ 1000 @ 25 mhz 5,2,1 35 @ 50 mhz 290 1.75 370 1008cs-122x_l_ 1200 @ 7.9 mhz 5,2 35 @ 50 mhz 250 2.0 310 1008cs-152x_l_ 1500 @ 7.9 mhz 5,2 28 @ 50 mhz 200 2.3 330 1008cs-182x_l_ 1800 @ 7.9 mhz 5,2 28 @ 50 mhz 160 2.6 300 1008cs-222x_l_ 2200 @ 7.9 mhz 5,2 28 @ 50 mhz 160 2.8 280 1008cs-272x_l_ 2700 @ 7.9 mhz 5,2 22 @ 25 mhz 140 3.2 290 1008cs-332x_l_ 3300 @ 7.9 mhz 5,2 22 @ 25 mhz 110 3.4 290 1008cs-392x_l_ 3900 @ 7.9 mhz 5,2 20 @ 25 mhz 100 3.6 260 1008cs-472x_l_ 4700 @ 7.9 mhz 5,2 20 @ 25 mhz 90 4.0 260 1008cs-562x_l_ 5600 @ 7.9 mhz 5 16 @ 7.9 mhz 20 4.0 240 1008cs-682x_l_ 6800 @ 7.9 mhz 5 18 @ 7.9 mhz 40 4.9 200 1008cs-822x_l_ 8200 @ 7.9 mhz 5 18 @ 7.9 mhz 25 6.0 170 1. when ordering, specify tolerance , termination and packaging codes: 1008cs- 822x jlc tolerance: f =1% g = 2% j = 5% (table shows stock tolerances in bold.) termination: l = rohs compliant silver-palladium-platinum-glass frit. special order: t = rohs tin-silver-copper (95.5/4/0.5) or s = non-rohs tin-lead (63/37). packaging: c =7 machine-ready reel. eia-481 embossed plastic tape (2000 per full reel). b = less than full reel. in tape, but not machine-ready. to have a leader and trailer added ($25 charge), use code letter c instead. d = 13 machine-ready reel. eia-481 embossed plastic tape. factory order only, not stocked (7500 per full reel). 2. inductance measured using a coilcraft smd-a fixture in an agilent/hp 4286a impedance analyzer with coilcraft-provided correlation pieces. 3. tolerances in bold are stocked for immediate shipment. 4. q measured using an agilent/hp 4291a with an agilent/hp 16193 test fixture. 5. srf measured using an aglilent/hp 8753d network analyzer and a coilcraft smd-d test fixture. 6. dcr measured on a cambridge technology micro-ohmmeter and a coilcraft ccf840 test fixture. 7. current that causes a 15c temperature rise from 25c ambient. 8. electrical specifications at 25c. see qualification standards section for environmental and test data. refer to doc 362 ?soldering surface mount components? before soldering.
|
